Trades · Pricing

Flat rate vs time and materials: how to price trade jobs.

Flat-rate pricing quotes one fixed price per task before work starts, while time and materials bills the hours and parts actually used. Most residential service shops use flat rate for repeatable work and keep time and materials for jobs nobody can scope in advance.

How you price a job affects more than the invoice. It changes how customers react at the door, how your technicians spend their time, and whether a slow tech or a fast one makes the shop more money. Here is how the two main methods work, where each fits, and how to build flat-rate prices that cover what the business actually costs to run.

What’s the difference between flat rate and time and materials?

Time and materials (T&M) bills an hourly labor rate for the time spent, plus the parts used, usually with a markup. The customer finds out the final price when the job is done.

Flat rate sets one price for a defined task, such as replacing a capacitor, swapping a 50-gallon water heater or adding a circuit. The price includes the expected labor, parts and overhead, and the customer agrees to it before work starts. If the job runs long, the shop absorbs it; if it goes quickly, the shop keeps the difference.

Why do customers often prefer flat rate?

Because they know the number before saying yes. With T&M, a homeowner watching the clock tends to wonder whether the tech is working slowly, and an estimate that turns into a bigger invoice is a common source of disputes and bad reviews. A flat price removes that worry, and it makes it easy to offer choices, such as a repair, a repair with a maintenance add-on, or a replacement, each with its own price.

Flat rate also changes what the shop rewards. Under T&M, a faster, more skilled tech produces a smaller invoice for the same job. Under flat rate, that speed shows up as more jobs per day at the same price per job.

When does time and materials make more sense?

T&M is the fairer method when nobody can know the scope up front:

  • Diagnostic and troubleshooting work where the problem isn’t known yet. Many shops charge a set diagnostic fee, then quote the repair flat rate once they know what’s wrong.
  • Remodels and unusual jobs with hidden conditions behind walls, under slabs or in older wiring.
  • Commercial and contract work where the customer expects T&M billing or the contract specifies it.
  • One-off tasks you haven’t done enough times to price with confidence.

Plenty of shops run both: flat rate for the service menu, T&M for the rest, with a not-to-exceed figure when the customer needs a ceiling.

How do you build a flat-rate price?

A flat-rate price has three parts: labor, materials and a margin that covers overhead and profit. Work through it one task at a time.

  • Estimate the time. Use your own job history where you have it: how long the task takes a typical tech, including setup, travel within the job and cleanup. Use the typical time, not your fastest tech’s best day.
  • Find your real cost per billable hour. Add up a year of overhead: rent, trucks, fuel, insurance, office staff, software, tools and the owner’s own pay. Divide it by the hours your techs actually bill in a year, not the hours they’re on the clock. Add the tech’s wage and payroll costs per hour. That total is what an hour of work costs you before any profit.
  • Price the parts. Use current supplier costs and apply your parts markup.
  • Add your profit margin on top of cost, and round to a clean price.

Many small shops find their true cost per billable hour is far higher than they assumed, because techs bill fewer hours than they work once you subtract drive time, callbacks, training and slow days. If your prices were set by copying the shop down the street, this step is where you’ll find out whether they actually cover your costs.

What’s the difference between markup and margin?

This trips up a lot of pricing. Markup is the percentage you add to cost. Margin is the percentage of the selling price that’s left after cost. They aren’t the same number:

  • A part that costs $100, marked up 50%, sells for $150. Your margin is $50 out of $150, or about 33%.
  • To earn a 50% margin on that $100 part, you need to sell it for $200, which is a 100% markup.

If you set a margin target, such as keeping 40% of revenue after direct costs, and then apply 40% as a markup, you will come up short on every job. Decide which number you’re targeting, and do the math the same way every time.

How do you keep flat-rate prices accurate?

  • Review prices at least once a year, and sooner when supplier prices, wages or insurance jump.
  • Compare estimated and actual time. If a task routinely takes longer than its price assumes, the price is wrong, or the task needs a better description.
  • Track callbacks. Repeat visits on flat-rate jobs come out of your margin, so watch which tasks and which techs generate them.
  • Watch how often quotes are accepted. Very high acceptance can mean you’re cheap; very low can mean you’re expensive or the options aren’t clear.

Keep the price book where every tech can see it on the job, so the same task gets the same price no matter who quotes it.

How DomoDomu Field Service handles pricing

DomoDomu Field Service is in early access for HVAC, plumbing and electrical shops with 1 to 15 technicians. It isn’t open for sign-up yet, and pricing will be published before launch. Its price book holds items priced flat rate or at cost plus your markup, and you can start from an HVAC, plumbing or electrical starter list or import your own from a CSV file, including exports from Jobber and Housecall Pro.

Quotes are built from the price book, with two to four options side by side or optional add-ons. The customer opens the quote from a link, chooses an option, signs on screen and can pay a deposit, and the approved quote becomes a job ready to schedule. Reports include quote conversion and callback rates per tech. See how quotes, invoices and payments work.

Quote it, schedule it, get paid for it.

DomoDomu Field Service is in early access for HVAC, plumbing and electrical shops with 1 to 15 technicians. Tell us about your shop to be one of the first.